All new SSA DM150.2 amplifier

[Aaron Clinton 2,372]

We have finally released our new amp.  It is a tiny tiny production run to see how people like them.  Meant for the high end, SQ market, without the European price tag.  If this model moves as well as I hope, it will help spawn another model in the line up soon.

https://store.soundsolutionsaudio.com/ssa-dm150-2-2-channel-amplifier-150w-x-2-ch-or-500w-x-1-ch/

Introducing the all new SSA DM150.2 amplifier. An old school approach, with updated components, for the most discerning of ears. If your front stage is lacking warmth and clarity, its time to upgrade. Our first amplifier in our high-end, sound quality, Class- A/B - Demon amplifier line. The SSA DM150.2 is the elite choice for that high end active front stage, premium passive components, and especially a sound quality sub (SSA Demon). We've incorporated direct inputs for those competition installs that use an external DSP and want their amp to be a pure gain block. Stellar looks to match the design and components. Don't let your speakers or your ears down, #levelup to the all new SSA DM150.2 amplifier.
 

• 150 Watts RMS X 2 @ 4 Ohm
• 500 Watts RMS X 1 @ 4 Ohm
• Angled Terminals for show quality installations
• Full Complimentary low distortion Class AB design
• Tiffany Style RCA connectorsFull Complimentary low distortion Class AB design
• Butterworth Crossover Filters for premium level performance
• An extra pair of input connectors for a direct input that will bypass the crossover so the amp can act as a gain block
• The op amps featured are TI chips w/BB technology high performance audio grade IC's
• Docking Pads® to reduce vibration & extend the life the amplifier
• DC, Short Circuit, Thermal & Overload Protection, on board fusing
• Diagnostic LEDs

Specifications

OUTPUT POWER @ 14.4V input
RMS per channel at 4 Ohms	150 W x 2 CH
RMS per channel at 2 Ohms	250 W x 2 CH
RMS Bridged Mono at 4 Ohms	500 W x 1 CH
RMS Mono at 1 Ohm	N/A
INPUT SENSITIVITY	200mV - 6.0V
FREQUENCY RESPONSE	10Hz - 30KHz +/- 0.5dB
THD	LESS THAN 0.01%
S/N RATIO	> 103 dB
CHANNEL SEPARATION	> 91 dB

DAMPING FACTOR @100Hz 4 ohm	> 200
CROSSOVER RANGE
High Pass, 12dB/Octave	80-1.2K Hz
Low Pass, 24dB/Octave	10Hz - 250Hz
Subsonic	N/A
Variable Bass Boost (0 to +12 dB bass boost at 45 Hz)	Yes
Phase Shift (0 - 180 degrees)	No
Fusing	3 x 40A
Size (L x W x H) in	16.4 x 8.9 x 2.2

[Randal Johnson 544]

Very nice Amplifier 

[Aaron Clinton 2,372]

1 hour ago, Randal Johnson said:

Very nice Amplifier 

Thanks, this is right up your alley.  But you're never going to switch.  Hahaha.

[Godsmack 361]

Looks sharp. Not a bad price point either.
 

J

[Aaron Clinton 2,372]

On 10/11/2019 at 4:06 PM, Godsmack said:

Looks sharp. Not a bad price point either.
 

J

Thanks, let's hope they start moving.

[Godsmack 361]

3 hours ago, Aaron Clinton said:

Thanks, let's hope they start moving.

I'm sure they will.

J

[///M5 2,833]

Wish I had a car that needed some tunes!  Love the heatsink!!

[Aaron Clinton 2,372]

8 hours ago, ///M5 said:

Wish I had a car that needed some tunes!  Love the heatsink!!

[Randal Johnson 544]

On 10/11/2019 at 2:55 PM, Aaron Clinton said:

Thanks, this is right up your alley.  But you're never going to switch.  Hahaha.

Thank You for understanding Sir.

Just a thought, this would be a great amplifier to run as a pair active on your component set. But not as you would normally think, use one amplifier to run the left side and another amplifier to run the right.

From the specs, there should be enough amplifier  channel separation to make it work and have excellent system left and right channel separation. 

Edited October 19, 2019 by Randal Johnson

[Aaron Clinton 2,372]