Im back, Ready for a dumb question?

[tac2137 2]

Its been a while since i have kept up with the audio industry and even when i did i was still a rookie. I was lucky enough to have a guy by the name of Alton from this same forum make me box measurements for my car but sadly my car was stolen right before i got to install everything in late 2012. I finally have a car with a big enough trunk to do it all over again hah. So know for my question. I have Two Sundown SA-12 D4's that will be running on a Sundown Saz-1500d v.3 WIth 1/0 gauge xs wire. My question is where and what are your opinions on trusted inline fuse holders that will fit my wire gauge and also how many should i get? Im guessing two. I have seen some pretty pricey holders so i would like to stay under $30-$35. 

[S.DeYoung 968]

Really you only need one close to your battery on the power wire, you could use another towards the amplifier just in case. Here are a few examples from the SSA store:

 

http://store.soundsolutionsaudio.com/products/machined-aluminum-anl-fuse-block.html

 

http://store.soundsolutionsaudio.com/products/shanlsc-anl-fuse-holder-sky-high-car-audio.html

 

http://store.soundsolutionsaudio.com/products/shanla-anl-fuse-holder-sky-high-car-audio.html

[altoncustomtech 773]

Welcome back!

 

I still have that design too, lol.  If you need another just let me know.

 

BTW, I agree with Sean's recommendations.  

[tac2137 2]

Really you only need one close to your battery on the power wire, you could use another towards the amplifier just in case. Here are a few examples from the SSA store:

 

http://store.soundsolutionsaudio.com/products/machined-aluminum-anl-fuse-block.html

 

http://store.soundsolutionsaudio.com/products/shanlsc-anl-fuse-holder-sky-high-car-audio.html

 

http://store.soundsolutionsaudio.com/products/shanla-anl-fuse-holder-sky-high-car-audio.html

Thanks a lot. 

[tac2137 2]

Welcome back!

 

I still have that design too, lol.  If you need another just let me know.

 

BTW, I agree with Sean's recommendations.  

Sweet! I think my trunk is a little bigger than my last and its not a hatchback. Do you think the same measurements will sound just as good?

[SacredTanakh 67]

Its been a while since i have kept up with the audio industry and even when i did i was still a rookie. I was lucky enough to have a guy by the name of Alton from this same forum make me box measurements for my car but sadly my car was stolen right before i got to install everything in late 2012. I finally have a car with a big enough trunk to do it all over again hah. So know for my question. I have Two Sundown SA-12 D4's that will be running on a Sundown Saz-1500d v.3 WIth 1/0 gauge xs wire. My question is where and what are your opinions on trusted inline fuse holders that will fit my wire gauge and also how many should i get? Im guessing two. I have seen some pretty pricey holders so i would like to stay under $30-$35. 

I know how that is, alton did a design for 6 ssa dcon 15s and my truck got wrecked before I had a chance to build it.

[altoncustomtech 773]

 

Welcome back!

 

I still have that design too, lol.  If you need another just let me know.

 

BTW, I agree with Sean's recommendations.  

Sweet! I think my trunk is a little bigger than my last and its not a hatchback. Do you think the same measurements will sound just as good?

 

 

From what I'm seeing it was 37" x 17.5" x 17.5" tuned to 32hz with 56sqin of port area.  As long as it would fit it should be fine.  Like I said, if you need it redesigned to fit the new car just let me know.

[tac2137 2]

 

Its been a while since i have kept up with the audio industry and even when i did i was still a rookie. I was lucky enough to have a guy by the name of Alton from this same forum make me box measurements for my car but sadly my car was stolen right before i got to install everything in late 2012. I finally have a car with a big enough trunk to do it all over again hah. So know for my question. I have Two Sundown SA-12 D4's that will be running on a Sundown Saz-1500d v.3 WIth 1/0 gauge xs wire. My question is where and what are your opinions on trusted inline fuse holders that will fit my wire gauge and also how many should i get? Im guessing two. I have seen some pretty pricey holders so i would like to stay under $30-$35. 

I know how that is, alton did a design for 6 ssa dcon 15s and my truck got wrecked before I had a chance to build it.

 

Damn, Im still upset that i didnt get to install it yet but at the same time im extreamly happy that  i didn't because i would no longer have anything. 

[tac2137 2]

 

 

Welcome back!

 

I still have that design too, lol.  If you need another just let me know.

 

BTW, I agree with Sean's recommendations.  

Sweet! I think my trunk is a little bigger than my last and its not a hatchback. Do you think the same measurements will sound just as good?

 

 

From what I'm seeing it was 37" x 17.5" x 17.5" tuned to 32hz with 56sqin of port area.  As long as it would fit it should be fine.  Like I said, if you need it redesigned to fit the new car just let me know.

 

I don't get off work till 2am but i should be off this Friday so ill probably double check my trunk and let you know then.