Welcome to the IHoP v.2

[dem beats 1,223]

56 minutes ago, Adrian_D said:

Yay transmission rebuild:

 

 

All the kings horses and all the kings men couldn't get me to put a transmission together again.

[nem 2,019]

10 hours ago, dem beats said:

And make her a handmade card.

 

Broads love that shit.  Glue a leaf to it  and shit will Be on like donkey Kong.

Hand written love note is always a good addition too. 

[nem 2,019]

On 3/16/2016 at 9:50 AM, ///M5 said:

Good.  If you need something call   

I just wanted to let everyone know that Sean"s equipment is amazing  (Polytec that is)

I got to spend about 4 hours setting up measurement points to measure micron movements, then run it in the Doppler software and watch 3 different views of the sonotrode, we then made some material cuts to get the results we needed to make sure there were no frequencies in our desired operating range and ran the Doppler again to see if the face of the sonotrode was working optimal.  It was truly awesome for me to get to do this and see how it works.

I now have a much better understanding for how small those unit can measure and how the Doppler graphs work. 

I worked my manager pretty hard to buy me one, but so far he is resisting. 

[nem 2,019]

6 hours ago, Adrian_D said:

Yay transmission rebuild:

 

 

Lot of fun there!

[nem 2,019]

5 hours ago, dem beats said:

Need to buy more weight.

 

Bangin out 300 for reps finally.  That feels so juicy. And I also feel like a bitch.  I used to warm up with 350 So I could bang out 720 for a few reps on the smith or >600 free.

C'est la vie.

 

Ain't nothing but a peanut.

Beast mode!

[nem 2,019]

I finally got to spend time with a very good buddy in his element. Over the many years of working in my facility, I have help him develop die cutter stations for the nonwovens application. Yesterday we spent the day at his machine shop and way more than I had expected! I even got to make some cuts and set up the tool angle for sharpening. 

Here is a link to give you a little look.

http://www.icd-inc.com/gallery/

[MKader17 332]

6 hours ago, dem beats said:

Need to buy more weight.

 

Bangin out 300 for reps finally.  That feels so juicy. And I also feel like a bitch.  I used to warm up with 350 So I could bang out 720 for a few reps on the smith or >600 free.

C'est la vie.

 

Ain't nothing but a peanut.

300 on what?

I consulted a multi rep max chart and I should now be in the 700 club! I based everything on a 5 rep "max" even though I do 5 sets of 5 for everything but DL.

Doing 2 plates on squats now. Can't wait to be doing 2 plates on Bench

[///M5 2,833]

Was it a single point or scanning?  They have both.  I assumed single from the text.

[///M5 2,833]

1 hour ago, nem said:

I finally got to spend time with a very good buddy in his element. Over the many years of working in my facility, I have help him develop die cutter stations for the nonwovens application. Yesterday we spent the day at his machine shop and way more than I had expected! I even got to make some cuts and set up the tool angle for sharpening. 

Here is a link to give you a little look.

http://www.icd-inc.com/gallery/

Awesome!!

[Penguin4x4 1,761]

15 hours ago, ///M5 said:

Shit.  My wife turns 40 this weekend.  Any ideas for a gift??  

 

One of these. Fun times for all.

 

[Tirefryr 1,742]

14 hours ago, dem beats said:

And make her a handmade card.

 

Broads love that shit.  Glue a leaf to it  and shit will Be on like donkey Kong.

That would be Donkey Dong since we're speaking of Sean.

[Tirefryr 1,742]

Dammit, I drove an older Mustang and I REALLY  enjoyed it more than driving Ava.  It's like the difference between my truck and Lincoln.  I like both, but the truck is just so raw and in your face.  The Lincoln is quiet, soft, and relaxing, like you're not even driving.  

I don' think I should keep this car.  

[Penguin4x4 1,761]

Thanks for all the support; I think everything's calmed down...for now.

 

[Penguin4x4 1,761]

[Penguin4x4 1,761]

[nem 2,019]

5 hours ago, ///M5 said:

Was it a single point or scanning?  They have both.  I assumed single from the text.

We did 20 points across the sonotrode, I believe.

[nem 2,019]

PSV-400 and PSV A420

[Penguin4x4 1,761]

[Penguin4x4 1,761]

[Penguin4x4 1,761]

[sandt38 448]

11 hours ago, nem said:

I finally got to spend time with a very good buddy in his element. Over the many years of working in my facility, I have help him develop die cutter stations for the nonwovens application. Yesterday we spent the day at his machine shop and way more than I had expected! I even got to make some cuts and set up the tool angle for sharpening. 

Here is a link to give you a little look.

http://www.icd-inc.com/gallery/

Very cool!

[Penguin4x4 1,761]

Well ain't that some shit...my alma mater made it to the second round. Go Jacks!

[Penguin4x4 1,761]

Creative little shit, I'll give him that.

 

 

[Tirefryr 1,742]

That guy's AMAZING!

[dem beats 1,223]

13 hours ago, MKader17 said:

300 on what?

I consulted a multi rep max chart and I should now be in the 700 club! I based everything on a 5 rep "max" even though I do 5 sets of 5 for everything but DL.

Doing 2 plates on squats now. Can't wait to be doing 2 plates on Bench

I can squat it about 10 times, bench 2-3, deadlift indefinitely depending on time between reps.