Hyundai elantra HB

[holykaos 2]

New box for 3 8s

What would the ohm load be for 3 sets of 4 ohm vc's

[Mtopper 23]

multiple different ohm loads.

all parallel equals

.667 ohms

all subs run parallel then in series

6 ohms

all subs series then run in parallel

2.667 ohms

all series subs then series run in box

24 ohms

if its still the SA8 dual 4s.

if its just single voice coil 4 then its

parallel

1.33 ohms

series

12 ohms

[holykaos 2]

Well what i really should find out it will my amp be stable at the lower ohm loads. I have the calc. stuff for ohms just kind of lazy on figuring it out after doing the math for my box.

[holykaos 2]

So i ordered 2 more sa-8s and 1 more hifonics 1200.1 there on the way now i just have to get the stuff to do a re build.

[holykaos 2]

So here's a new update on this system i have changed my mind a few times and went back and forth on what i wanted to do. So i am now doing 4 sa8 dual 4's in a new box i have been working on.

There will be some plexi and a few other little things i plan on doing to it.

As for an amp i believe i am going with the hifonics colossus. Going to wire each pair to 1 ohm and run them off both channels.

On another note i spent the weekend doing a few things to the car.

That's my 2 year old helping me roll out the fat mat.

Next step will be picking up some truck bed liner and doing the out side of my roof and putting some cld tiles on the inside of it.

Edited February 7, 2012 by holykaos

[ssh 924]

Got your little helper

How's the fatmat sticking?

[holykaos 2]

Stuck down really good i was having issues pulling it back up to move it around a little when it was just laying on the floor. But we will see how it holds up.

[ssh 924]

Its butyl based right? Glad its working. Nothing beats a quiet ride.

[holykaos 2]

It does not seem like the old fat mat every one was talking about, there's no smell it sticks really well and rolled out very easy. Its also some heavy stuff out of the 4 rolls i have(each roll is 50sft) they weigh in around 25 pounds each.

[ssh 924]

It does not seem like the old fat mat every one was talking about, there's no smell it sticks really well and rolled out very easy. Its also some heavy stuff out of the 4 rolls i have(each roll is 50sft) they weigh in around 25 pounds each.

That's what I was wondering. Glad it's been changed.

[TRP 42]

Glad to see more AZ people here, and nice looking build also!

[holykaos 2]

Been looking for some people in az but i live along ways away from most of the people i have seen on here. And all the shows and stuff take place near phoenix about 4 hours from me.

[mccleery3 166]

Love seeing the next generation getting involved You'll love those 4 SA's

[16K 159]

What box designing program is that??

Tuned in.

[ssh 924]

What box designing program is that??

Tuned in.

Google Sketchup, isn't made specifically for enclosures, but works quite well.

[16K 159]

What box designing program is that??

Tuned in.

Google Sketchup, isn't made specifically for enclosures, but works quite well.

kk thanks!

[holykaos 2]

Ya its sketch up. Works really well takes some time to get used too but after you get the hang of it, its not too hard. Any ways i did a little bit more finished the Fat mat on the floors not much to see there and ran some up the pillars. Re-ran my Rca's and my remote turn on down the center of the car. Also found something i forgot i had in my car the pioneer I-pod control thing for the dvd 3100. So i pulled it out and freed up a little space in my dash.

The run of rca's 2 pairs.

Behind the scene look.

The pioneer unit.

And all the front trim is back in just have to put my seat's back in up front. I am leaving the rear seats out until my new box is built and in.

[holykaos 2]

Small update. Been working on a few things at once first the new box is starting to come together. I laid it out put the top and all sides on. Going to cut the holes for my 2 ports and the 4 subs some time today.

how i made the ports.

Any one take a guess what that is and where it went.

[ssh 924]

expanding foam. Used it to make a mold / base off of.

[gbn 0]

lookin good love the port color

[holykaos 2]

Lol no mold for the expanding foam but after 12 cans of big gap filler my hatch and all the open areas in the back of my car no longer make any noise.

[holykaos 2]

Few updates really fast. Ports are now in and not going any where.

This is what 2 of the 4 look like on top.

[KyleBrown 121]

looking really nice. Great work so far man

[gbn 0]

baby tanks

[holykaos 2]

And a few more little things.

Stripped my old system out. All the trim panels and all so now its just kind of hanging around until i drop the new system in.

Got board and textured the ports just because i could.