2010 Camry build log.

[gcs8 10]

no it doesn't, its part of the factory wiring tho.

[Robert.Metzel 4]

On the 2009's I found out it's the on-off switch for the keyless entry system installed at the port. So its probably the same for the 2010. Made by Audiovox and its a factory install.

[gcs8 10]

so i was short like 3 or 4 peaces of SPL tile but oh well, could be worse. wire rca's should be hear in a couple days then LLP will get hear then my sludge will get hear. when't to go see jnralp00 (Doug) and the guys at all star audio all of the great guys. Doug's setup kicked the shit out of my old setup, i got owned lol. any way more pics.

even put in a seat so i could drive around to day after i ran out tiles.

[CrazyKenKid 64]

o wwow nice job!! did you ever figure out what that button was for?

[gcs8 10]

no i will run by the dealer ship Monday and ask, will let you know.

[MrViciousToys 0]

its the switch to make the brakes work, when the car goes outta control

[gcs8 10]

small update, got bored so i ran my remote gain for the saz-3000D.

[gcs8 10]

more packages came in he he he.

ups must hate me

old wire.......... any one want it?

had to lube up the new wire.

i need to learn how to cut wire.

[gcs8 10]

ran my power wire to day.

what wire i have left. hoping its enough to redo my big 3

[kjbulldog 0]

what kind of wire is your old wire? and how much do you want for it? I may want it for my big three...good work btw...how do you like the mlv, im guessing its luxury liner

[gcs8 10]

its monster 4ga, 20 + shipping, i may be holding on to the fuse holder (its suppose to be a 1/0 holder.) 16'4'' and 8.5". ty for the complements, its SS LLP and i haven't got it in place yet just tossed it in there for now. will let you know. still trying to figger out how i want to do it, got some sludge cumming tomorrow then 2 days dry time then LLP then wiring.

[eggyhustles 33]

I guess i missed the "sq" part.

[gcs8 10]

I guess i missed the "sq" part.

how so?

[gcs8 10]

got board and decided i needed some better wire management so hears how it came out. also the dog came to watch me.

[eggyhustles 33]

I guess i missed the "sq" part.

how so?

what makes that an sq setup?

[gcs8 10]

the FI Q is a SQ sub, nothing is geared towards SPL, the sound deading and LLP mats and sludge is going to make it posable to lission from rather low vol. things of this nature.

[eggyhustles 33]

I know that

But, just because you have sq subs does not make your setup an sq setup.

[Dictator1992 6]

ooo this is getting personal!! as long as it sounds good to his hear its sq enough

[gcs8 10]

so on Friday my Spectrum Sludge came in but they for got to send me the Sludge part.... so i called ANT from SS, he said that who ever packed it for got it and he would send me out the activator but it wouldn't make it to me until ~ Wednesday. sooo, no updates tell until then most likely.

[gcs8 10]

small update. its hard to get this thick wire in the holes.

i am going to haft to use the old ground for the mids and high's amp, cant find my other distro block.

[gcs8 10]

update * put a sheet of LLP under the back seat today, for got to take pic and its a bitch get the back seat back on. *

[CrazyKenKid 64]

hey want to know how i cut 1/0 wire? lol

I cut it with this tool which i got from home depot (tool on the left) it cuts through the wire with minimal effort, this tool insure proper cuts all the time.

I use the knife in the center to cut off the jacket of the wire.

and use the tool on the end to crimp the wire to the terminal and let me tell you that bitch is on there solid!!!!!

and

sorry a little hard to tell with the terminal i used but let em tell you that thing isn't coming out!

[CrazyKenKid 64]

cutters 35$ at home depot (cad so about 25 USD lol)

Knife 5$ at home depot

Crimper 50$ on ebay! it is called a hydrolic 8ton crimper.

i hope this helps you in the future

[gcs8 10]

TY very much, i wish you guys lived closer i would rent the tools from you for the day.

[gcs8 10]

UPDATES!

did my trunk a while back just never got a pic of it.