Welcome to the IHoP

[ricksi30 923]

Funny too because the steak should be conductive.

When they cut the steak the Saw Stop is not installed.

[///M5 2,833]

I figured a cylinder would be the best. I need around .6-.7 cuft. 10" diameter ~13-14" long. Birch cap on both ends and bam.

Love all the ideas. Thanks guys. Completely open to more. PVC is winning atm

What about those cheap small stainless trash cans? Brace the inside with wood. Build your baffles and glass and you're good to go.

The issue with sonotube is both sides are waxed and you have to get through that before painting or glassing. Actually they weather quite well as long as you seal the edges. They can sit outside at jobsites for quite some time before being affected..

Stainless would be sweet. Have you seen some for sale somewhere?

Big Lots, etc. . .

Ha, I only shop online. I'll have to run out to one of those type stores.

[///M5 2,833]

6 if you count the horns, but those won't be in matching enclosures. Hell, have no idea what I am going to do for those at all yet. Have to pick a horn body first.

Why not just build one large enclosure out of FG?

Cosmetic reasons only. I will probably connect the two "tube" enclosures with the one for the horn.

[///M5 2,833]

Ideas for ya Sean

http://www.sidebysid...akertubbie.html

http://www.westmarin...-light-bar.html

http://www.westmarin...&classNum=50199

http://www.rockthebo...nespeakers.html

Hope these help.

J

Thanks for searching J...what I want will take a bit more space than that

[///M5 2,833]

I might throw up some other goodies, such as:

Dayton RS180's

Dayton RS28a

Seas Excel W18

Seas CA18RNX

Alpine XT19 variant

Have some more, just having a brainfart. Open to getting rid of anything.

iirc you have a mach 5 ixl?

i regret not getting one back in the day, went with an cheaper sub from Ascendant audio.

edit: not that i'm interested in buying it, just dont have a use for it.. i just remember random shit haha

I have the prototype and initial IXL 12. All others were built based on the one I have. No further changes, but there were none before it either.

[///M5 2,833]

And it is not for sale. Forgot I had it though Eventually it'll go into my office.

[Quentin Jarrell 671]

_{I vote go this route}

_{http://www.dragonplate.com/ecart/categories.asp?cID=121}

[Quentin Jarrell 671]

[///M5 2,833]

Wow, fuck you. That would be seriously bad ass. I no longer want anything else.

Bastards don't seemingly make them in a 10" or 12" diameter though

[Godsmack 361]

Ideas for ya Sean

http://www.sidebysid...akertubbie.html

http://www.westmarin...-light-bar.html

http://www.westmarin...&classNum=50199

http://www.rockthebo...nespeakers.html

Hope these help.

J

Thanks for searching J...what I want will take a bit more space than that

I figured as much. Just hoped with lower prices that they might help get some ideas going.

J

[Tirefryr 1,742]

_{I vote go this route}

_{http://www.dragonpla...ies.asp?cID=121}

I was afraid to scroll down and see the price.

[Quentin Jarrell 671]

it look pimpin polished though

[Tirefryr 1,742]

6 if you count the horns, but those won't be in matching enclosures. Hell, have no idea what I am going to do for those at all yet. Have to pick a horn body first.

Why not just build one large enclosure out of FG?

Cosmetic reasons only. I will probably connect the two "tube" enclosures with the one for the horn.

You can cosmetically construct them any way you want, or do you not have time for that much detailed work?

[Tirefryr 1,742]

As if I don't know the answer to that.

[Quentin Jarrell 671]

• They can make whatever you want, we use them for our custom one offs for our circle track cars
  

[///M5 2,833]

And yes, I sent them an email. Hope I suck at their internet

[///M5 2,833]

it look pimpin polished though

Understatement. Super sweet with either a polished aluminum ass or gel coat matched to my hull. Perhaps Gel coat front polished ass.

[///M5 2,833]

6 if you count the horns, but those won't be in matching enclosures. Hell, have no idea what I am going to do for those at all yet. Have to pick a horn body first.

Why not just build one large enclosure out of FG?

Cosmetic reasons only. I will probably connect the two "tube" enclosures with the one for the horn.

You can cosmetically construct them any way you want, or do you not have time for that much detailed work?

I'd like to do them in a day. Many other projects that I need to tackle.

[///M5 2,833]

As if I don't know the answer to that.

ROFL. Answered anyways.

[///M5 2,833]

• They can make whatever you want, we use them for our custom one offs for our circle track cars
  

Fuck, so they are going to answer. I am scared to hear the quote and excited all at the same time. If I do those I am going to have to find some seriously pretty clamps to hold them onto the tower.

[///M5 2,833]

Perhaps I'll have to pull out the lathe and turn my own.

[///M5 2,833]

Wait, fuck me, the time thing again.

[ssh 924]

Funny too because the steak should be conductive.

Different table saw. First one was traditional, then second one was the fancy one.

[///M5 2,833]

I wanted to see him put his hot dog up there. He created it, show some balls. *pun intended

[topgun 262]

Yep, I bought one of those for work. Fantastic saw.

You can turn the saw stop off if you want to, necessary when cutting aluminum on the saw. Even if something is conductive it won't set it off unless you are touching it while cutting. On their normal hotdog demo, if the person doesn't hold it, and just rolls it into the blade it'll cut it in half.