Welcome to the IHoP

[Aaron Clinton 2,372]

Look at this near the bottom of the page...

http://pasmag.com/ca...ne-2012?start=5

[///M5 2,833]

Look at this near the bottom of the page...

http://pasmag.com/ca...ne-2012?start=5

Sweet indeed

[dem beats 1,223]

Look at this near the bottom of the page...

http://ipasmag.com/ca...ne-2012?start=5

Sweet indeed

...the blues goofy driver thingy?

[ricksi30 923]

Look at this near the bottom of the page...

http://ipasmag.com/ca...ne-2012?start=5

Sweet indeed

...the blues goofy driver thingy?

No the XCON!!!!!!!

[topgun 262]

RE Audio still exists?

[ricksi30 923]

RE Audio still exists?

Not in my opinion

[dem beats 1,223]

I didn't see the xcon!

I'll.check when I get home from the pc

[nem 2,019]

Look at this near the bottom of the page...

http://pasmag.com/ca...ne-2012?start=5

Sweet indeed

[Aaron Clinton 2,372]

RE Audio still exists?

Not in my opinion

They had a massive booth at SBN.

[ricksi30 923]

RE Audio still exists?

Not in my opinion

They had a massive booth at SBN.

It's sad, they seem more popular now than when they made good stuff.

[Aaron Clinton 2,372]

RE Audio still exists?

Not in my opinion

They had a massive booth at SBN.

It's sad, they seem more popular now than when they made good stuff.

[Adrian_D 520]

If I wanted to cut a 10" pvc pipe to a perfectly square end and have access to a table saw, skil saw, or radial arm saw how would you jig it so that I can cut it straight?

Cut an MDF ring with the ID equal to the pipe OD, or any other material which is rigid enough, mark 3-4 spots on the pipe at the desired length, slide the ring over the pipe and align it with the marks, use the ring as guide to cut or mark.

That's how I do it for PVC pipe and after marking the cut line, I freehand the cut with an angle grinder. It doesn't turn out as good as a perfectionist would want but it's pretty damn good

[ssh 924]

Edited June 7, 2012 by stefanhinote

[ssh 924]

Ass shot.

[Penguin4x4 1,761]

Kalashnikov in 6.8 Remington with reflex sights would be fun too

[Penguin4x4 1,761]

random penguin is random

[Tirefryr 1,742]

If I wanted to cut a 10" pvc pipe to a perfectly square end and have access to a table saw, skil saw, or radial arm saw how would you jig it so that I can cut it straight?

For anything above 4" I trim close to where needed, then make a couple plugs, install one on the known square end, fill with sand, install the other plug to a square line and roll it around a flush trim bit on the router table.

[dem beats 1,223]

Kalashnikov in 6.8 Remington with reflex sights would be fun too

Silenced. Large bore sub sonic/sonic optiond round on a black rifle is my dream home defence weapon. 300 blackout, or whatever that fat ass socom round is.

[Godsmack 361]

Fuckin A

J

[Penguin4x4 1,761]

Integrally silenced .458 SOCOM? Sounds good to me

[dem beats 1,223]

Integrally silenced .458 SOCOM? Sounds good to me

Dat be teh one. I dont care how its silenced. MN doesnt allow it either way though.

[dem beats 1,223]

!Makes for a good hog shooing black rifle from what i hear.

[///M5 2,833]

If I wanted to cut a 10" pvc pipe to a perfectly square end and have access to a table saw, skil saw, or radial arm saw how would you jig it so that I can cut it straight?

For anything above 4" I trim close to where needed, then make a couple plugs, install one on the known square end, fill with sand, install the other plug to a square line and roll it around a flush trim bit on the router table.

Sweet. Problem solved. I'll attempt the table saw, but slightly too long. If it works no worries, if not I'll install my end caps and flush them off.

<--feels like an idiot, lol

[///M5 2,833]

<--makes everything complicated

[///M5 2,833]

My speaker wire came today though so I can rewire the tower Monoprice ftw. Since 1' of it will be exposed white jacket ftw.