Welcome to the IHoP

[dem beats 1,223]

Speaking of lightweight, high horsepower, check out this dune buggy pulling wheelies in 5th Gear

Do want.

Once again proof turbos are awesome

Amen brother. I never doubted the glory of turbo boost.

[Luke.H 33]

Just test drove a Porsche Panamera Turbo and an X5 ///M.

Too bad the Panamera is so fucking ugly. It'd be a sweet car if not for that.

I am too old to care. For me the car needs to stir my inside and be nice on the inside, if its ugly on the outside I don't give a fuck. Obviously considering I am driving a soccer mom truck, lol.

From the front it's not bad. It's the ass that kills it. Just get a 911 Turbo, to hell with practicality.

[Mac N Cheese 90]

DEETROITTT

[S.DeYoung 968]

DEETROITTT

Raburn!

[Penguin4x4 1,761]

[Penguin4x4 1,761]

[ssh 924]

[Mac N Cheese 90]

That was close..

[Godsmack 361]

Get a chick who can do that in a strip club and watch the singles stack up.

J

[///M5 2,833]

Just test drove a Porsche Panamera Turbo and an X5 ///M.

Too bad the Panamera is so fucking ugly. It'd be a sweet car if not for that.

I am too old to care. For me the car needs to stir my inside and be nice on the inside, if its ugly on the outside I don't give a fuck. Obviously considering I am driving a soccer mom truck, lol.

From the front it's not bad. It's the ass that kills it. Just get a 911 Turbo, to hell with practicality.

Can't drive one of those daily with 2 children.

[///M5 2,833]

Singles, lol. Cheap bastard. It'd be $20's in this town.

[///M5 2,833]

Fucking imageshack

[Tirefryr 1,742]

I need a blow job.

[ssh 924]

Labyrinth TOP.

[///M5 2,833]

Concrete sink/countertop build

Empty mold

With plexi added for the drain

Showing with drain tube, it will float above the plexi so there will be a concrete funnel bringing all the water into the drain and not near its edges to prevent leaks (or so I hope  )

Drain Close-up

A little metal support added (support boards will be screwed in before cement is poured)

Drain with support (removable so I can pull the support out)

More shots of reinforcement

Question being is there enough metal in there? In particular the rear spot by the drain. I can easily even “screw” in supports through the mold on that side being the won’t be visible and can be whacked off with the angle grinder later.

[///M5 2,833]

And yep, was perfect but I dropped it munging the edge.

[///M5 2,833]

The actual sink portion that is

[///M5 2,833]

Fuck me top

[Tirefryr 1,742]

Just an FYI, you will see the holes from the screw heads in the concrete. Cover them with candle wax. I'd also caulk the edges of the mold as well.

[///M5 2,833]

Teo, for you:

[///M5 2,833]

Just an FYI, you will see the holes from the screw heads in the concrete. Cover them with candle wax. I'd also caulk the edges of the mold as well.

I haven't siliconed the corners, edges yet. Like the candle wax idea though The screws are countersunk so I can cover them with what was originally going to be silicone, but it'll be way easier to trim the wax up nice

[///M5 2,833]

Exactly why the bracing isn't screwed in yet

[lithium 358]

holy shit..

[ssh 924]

Fuck, that's nuts.

[ssh 924]

Tuned in for the rest of the sink.