Jump to content
mrray13

Welcome to the IHoP

Recommended Posts

I just used the quickrete quick mix, just add water.

Drop one 60lb bag in wheelbarrow, slash a cross, flip bag over, pull up from sides and the bag will split in two emptying out. I did two bags to a wheelbarrow (otherwise I'd probably spill the shit moving it across the front yard to back yard).

Then had a spray gun type handle on the end of the water hose. Spray, lightly mix concrete around with hoe, push all concrete forward in wheelbarrow, spray more water into bottom (like a little lake), then start pulling down concrete mixing with hoe until the large puddle starts to thicken.

Then keep pulling down more concrete and adding water. Spray the wheelbarrow between each run, it'll help keep the concrete from sticking on the bottom.

The key is just to mix the shit a lot, get rid of any dry spots where it's still powder, and have a hose right next to where your mixing.

I'm certainly no pro but it worked for what I was doing. Just a small slab to go under a work table in the backyard.

Ah, I am pouring a sink/countertop and mixing the sand, rock and portland cement AND color which means I have to mix the living shit out of it. I don't own a wheel barrow either and have to have a big enough container to do it in one pour. Was hoping you had something clever that would relay to that :) Thanks though.

I would advise you to get a concrete mixer in that case. I despise mixing concrete and would rather buy it ready for pouring or hire a mixer. Life is so much easier with a mixer.

I was going to use the Vitamix. :P

Actually I had thought a mixer was a good plan. Was hoping to not pay to rent it though.

*out of curiosity since I will mix too much, what do you do with the leftover when you do that?

Share this post


Link to post
Share on other sites

I just used the quickrete quick mix, just add water.

Drop one 60lb bag in wheelbarrow, slash a cross, flip bag over, pull up from sides and the bag will split in two emptying out. I did two bags to a wheelbarrow (otherwise I'd probably spill the shit moving it across the front yard to back yard).

Then had a spray gun type handle on the end of the water hose. Spray, lightly mix concrete around with hoe, push all concrete forward in wheelbarrow, spray more water into bottom (like a little lake), then start pulling down concrete mixing with hoe until the large puddle starts to thicken.

Then keep pulling down more concrete and adding water. Spray the wheelbarrow between each run, it'll help keep the concrete from sticking on the bottom.

The key is just to mix the shit a lot, get rid of any dry spots where it's still powder, and have a hose right next to where your mixing.

I'm certainly no pro but it worked for what I was doing. Just a small slab to go under a work table in the backyard.

Ah, I am pouring a sink/countertop and mixing the sand, rock and portland cement AND color which means I have to mix the living shit out of it. I don't own a wheel barrow either and have to have a big enough container to do it in one pour. Was hoping you had something clever that would relay to that :) Thanks though.

My uncle did exactly that. Counter tops and sinks in bathrooms. Also built his entire house, super modern.

Ill ask him today and see what he says. :)

Awesome, thanks!

Share this post


Link to post
Share on other sites

I just used the quickrete quick mix, just add water.

Drop one 60lb bag in wheelbarrow, slash a cross, flip bag over, pull up from sides and the bag will split in two emptying out. I did two bags to a wheelbarrow (otherwise I'd probably spill the shit moving it across the front yard to back yard).

Then had a spray gun type handle on the end of the water hose. Spray, lightly mix concrete around with hoe, push all concrete forward in wheelbarrow, spray more water into bottom (like a little lake), then start pulling down concrete mixing with hoe until the large puddle starts to thicken.

Then keep pulling down more concrete and adding water. Spray the wheelbarrow between each run, it'll help keep the concrete from sticking on the bottom.

The key is just to mix the shit a lot, get rid of any dry spots where it's still powder, and have a hose right next to where your mixing.

I'm certainly no pro but it worked for what I was doing. Just a small slab to go under a work table in the backyard.

Ah, I am pouring a sink/countertop and mixing the sand, rock and portland cement AND color which means I have to mix the living shit out of it. I don't own a wheel barrow either and have to have a big enough container to do it in one pour. Was hoping you had something clever that would relay to that :) Thanks though.

Portable mixer is your best bet; pour in the ingredients, turn it on and let it eat. Kinda like making a smoothie in a VitaMix :D Getting rid of the air is a bit of a pill also, best way I've seen besides a shaker table is to take a a bladeless Sawzall against the outside of the form until the bubbles stop forming.

Bladels sawzall?

Share this post


Link to post
Share on other sites

yeah, just take the blade out; bladeless :P

Share this post


Link to post
Share on other sites

*out of curiosity since I will mix too much, what do you do with the leftover when you do that?

Make a bird bath or some garden gnomes or somesuch

Share this post


Link to post
Share on other sites

pneumatic chisel with a hammer chisel bit might work if you turn regulator way down, but I doubt it

Share this post


Link to post
Share on other sites

Good turn out tonight! I was able to get a couple shots and plan on uploading them tomorrow.

Sweet, I'll look out for'em.

Funny question, do you guys ever use chainsaws?

I remember going through a haunt once and one of the guys ran through the public crowd with a chainsaw. I swore it was real but seems like that would be such a liability, like if he tripped, "Oh shit, sorry I just cut off your fucking head bro."

Yes we have a chainsaw, but there is no chain on it. The actor who carries it is 6'8" and scares the shit out of everybody.

I should have read further down. I could be that acto :)

You are always welcome to join in the fun. :)

Share this post


Link to post
Share on other sites

*out of curiosity since I will mix too much, what do you do with the leftover when you do that?

Make a bird bath or some garden gnomes or somesuch

Speed bumps in your neighbors drive way. ;)

Share this post


Link to post
Share on other sites

shaker table would be a fun tool to have, though...

Share this post


Link to post
Share on other sites

Drop excess off at the neighbors you don't like. :P

Share this post


Link to post
Share on other sites

Fuckin bolt on the tensioner assembly got rusted into the pully and ended up breaking..............time to buy a replacement assembly.

J

Share this post


Link to post
Share on other sites

I just used the quickrete quick mix, just add water.

Drop one 60lb bag in wheelbarrow, slash a cross, flip bag over, pull up from sides and the bag will split in two emptying out. I did two bags to a wheelbarrow (otherwise I'd probably spill the shit moving it across the front yard to back yard).

Then had a spray gun type handle on the end of the water hose. Spray, lightly mix concrete around with hoe, push all concrete forward in wheelbarrow, spray more water into bottom (like a little lake), then start pulling down concrete mixing with hoe until the large puddle starts to thicken.

Then keep pulling down more concrete and adding water. Spray the wheelbarrow between each run, it'll help keep the concrete from sticking on the bottom.

The key is just to mix the shit a lot, get rid of any dry spots where it's still powder, and have a hose right next to where your mixing.

I'm certainly no pro but it worked for what I was doing. Just a small slab to go under a work table in the backyard.

Ah, I am pouring a sink/countertop and mixing the sand, rock and portland cement AND color which means I have to mix the living shit out of it. I don't own a wheel barrow either and have to have a big enough container to do it in one pour. Was hoping you had something clever that would relay to that :) Thanks though.

I would advise you to get a concrete mixer in that case. I despise mixing concrete and would rather buy it ready for pouring or hire a mixer. Life is so much easier with a mixer.

I was going to use the Vitamix. :P

Actually I had thought a mixer was a good plan. Was hoping to not pay to rent it though.

*out of curiosity since I will mix too much, what do you do with the leftover when you do that?

I usually find a place for extra concrete around the yard. You won't mix way too much if mixers are the size of the ones here.

Share this post


Link to post
Share on other sites

I just used the quickrete quick mix, just add water.

Drop one 60lb bag in wheelbarrow, slash a cross, flip bag over, pull up from sides and the bag will split in two emptying out. I did two bags to a wheelbarrow (otherwise I'd probably spill the shit moving it across the front yard to back yard).

Then had a spray gun type handle on the end of the water hose. Spray, lightly mix concrete around with hoe, push all concrete forward in wheelbarrow, spray more water into bottom (like a little lake), then start pulling down concrete mixing with hoe until the large puddle starts to thicken.

Then keep pulling down more concrete and adding water. Spray the wheelbarrow between each run, it'll help keep the concrete from sticking on the bottom.

The key is just to mix the shit a lot, get rid of any dry spots where it's still powder, and have a hose right next to where your mixing.

I'm certainly no pro but it worked for what I was doing. Just a small slab to go under a work table in the backyard.

Ah, I am pouring a sink/countertop and mixing the sand, rock and portland cement AND color which means I have to mix the living shit out of it. I don't own a wheel barrow either and have to have a big enough container to do it in one pour. Was hoping you had something clever that would relay to that :) Thanks though.

I would advise you to get a concrete mixer in that case. I despise mixing concrete and would rather buy it ready for pouring or hire a mixer. Life is so much easier with a mixer.

I was going to use the Vitamix. :P

Actually I had thought a mixer was a good plan. Was hoping to not pay to rent it though.

*out of curiosity since I will mix too much, what do you do with the leftover when you do that?

I usually find a place for extra concrete around the yard. You won't mix way too much if mixers are the size of the ones here.

Got a bunch of blocks and puddles of concrete scattered around the yard? :lol:

Share this post


Link to post
Share on other sites

LET FREEDOM RING WITH A SHOTGUN BLAST

Share this post


Link to post
Share on other sites

Sean, you ever listen to Mingus?

Share this post


Link to post
Share on other sites

I laughed so hard I nearly crapped my pants

Share this post


Link to post
Share on other sites

I just used the quickrete quick mix, just add water.

Drop one 60lb bag in wheelbarrow, slash a cross, flip bag over, pull up from sides and the bag will split in two emptying out. I did two bags to a wheelbarrow (otherwise I'd probably spill the shit moving it across the front yard to back yard).

Then had a spray gun type handle on the end of the water hose. Spray, lightly mix concrete around with hoe, push all concrete forward in wheelbarrow, spray more water into bottom (like a little lake), then start pulling down concrete mixing with hoe until the large puddle starts to thicken.

Then keep pulling down more concrete and adding water. Spray the wheelbarrow between each run, it'll help keep the concrete from sticking on the bottom.

The key is just to mix the shit a lot, get rid of any dry spots where it's still powder, and have a hose right next to where your mixing.

I'm certainly no pro but it worked for what I was doing. Just a small slab to go under a work table in the backyard.

Ah, I am pouring a sink/countertop and mixing the sand, rock and portland cement AND color which means I have to mix the living shit out of it. I don't own a wheel barrow either and have to have a big enough container to do it in one pour. Was hoping you had something clever that would relay to that :) Thanks though.

I would advise you to get a concrete mixer in that case. I despise mixing concrete and would rather buy it ready for pouring or hire a mixer. Life is so much easier with a mixer.

I was going to use the Vitamix. :P

Actually I had thought a mixer was a good plan. Was hoping to not pay to rent it though.

*out of curiosity since I will mix too much, what do you do with the leftover when you do that?

I helped a guy do a concrete hearth place the other day. How big of pour are you doing? For polishing you are going to want something stronger than ~8,000psi so you don't pull the cement paste out when polishing. I doubt anything off of the redi-mix truck will do that in any reasonable about of time. For the higher strength I'd suggest looking at a lower water-cement ratio and adding plasticizers to keep it workable. Oh and vibrate it well too, along with smacking the sides of the form work with a rubber mallet.

Share this post


Link to post
Share on other sites

Sean, you ever listen to Mingus?

That answer is a yes.

Share this post


Link to post
Share on other sites

Sean, you ever listen to Mingus?

That answer is a yes.

Hey Topgun.. you know anything about building walls? lol

Share this post


Link to post
Share on other sites

I've built walls before.

Block, mud & sticks? :lol:

Share this post


Link to post
Share on other sites

We went for 80's in the days down to the 60s 2 days ago. Not fun.

J

Im loving this weather. :P

Still low 80s here and I love it. Went and played 18 holes. It was more or less an excuse to drink :P

Share this post


Link to post
Share on other sites

I've built walls before.

You're about 2 hours of me and i'm in need of some experience with building.

Share this post


Link to post
Share on other sites

I just used the quickrete quick mix, just add water.

Drop one 60lb bag in wheelbarrow, slash a cross, flip bag over, pull up from sides and the bag will split in two emptying out. I did two bags to a wheelbarrow (otherwise I'd probably spill the shit moving it across the front yard to back yard).

Then had a spray gun type handle on the end of the water hose. Spray, lightly mix concrete around with hoe, push all concrete forward in wheelbarrow, spray more water into bottom (like a little lake), then start pulling down concrete mixing with hoe until the large puddle starts to thicken.

Then keep pulling down more concrete and adding water. Spray the wheelbarrow between each run, it'll help keep the concrete from sticking on the bottom.

The key is just to mix the shit a lot, get rid of any dry spots where it's still powder, and have a hose right next to where your mixing.

I'm certainly no pro but it worked for what I was doing. Just a small slab to go under a work table in the backyard.

Ah, I am pouring a sink/countertop and mixing the sand, rock and portland cement AND color which means I have to mix the living shit out of it. I don't own a wheel barrow either and have to have a big enough container to do it in one pour. Was hoping you had something clever that would relay to that :) Thanks though.

I would advise you to get a concrete mixer in that case. I despise mixing concrete and would rather buy it ready for pouring or hire a mixer. Life is so much easier with a mixer.

I was going to use the Vitamix. :P

Actually I had thought a mixer was a good plan. Was hoping to not pay to rent it though.

*out of curiosity since I will mix too much, what do you do with the leftover when you do that?

I helped a guy do a concrete hearth place the other day. How big of pour are you doing? For polishing you are going to want something stronger than ~8,000psi so you don't pull the cement paste out when polishing. I doubt anything off of the redi-mix truck will do that in any reasonable about of time. For the higher strength I'd suggest looking at a lower water-cement ratio and adding plasticizers to keep it workable. Oh and vibrate it well too, along with smacking the sides of the form work with a rubber mallet.

Kwik-crete sells a 10-12K psi mix around here and acrylic is readily available as well. I'd just mix it straight with the acrylic and skip the water.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.

×