///M5

I did just buy 1.5lbs of Wagyu for dinner.

You You've always loved my beef.

I mean most coffee that is sold really isn't coffee. It's sugar and milk concoctions with a splash of coffee.Not really the norm here. People drink it mostly black. Either way, for something that can be so good making it so bad is insane.

Overall output will be higher further up the frequency range.

mmmmm pie

I'd expect that to be more than a $1000 situation

All out SPL AND get LOW are not going to happen. You just defined two near opposites.

Beware, that is still gross... 2" lift isn't trivial either. Make sure they are doing it safely, if not you are better off removing the seat. Anything more than about 7/8" requires extra fabrication.

Can't imagine how 90% of the world likes coffee. I was out and went to a chain this morning and the pizzle is hardly drinkable. And no, wasn't stupid enough to go to Starbucks as that shit I wouldn't feed to my plants.

I wouldn't eat a grilled eggplant either. Sprouts need FAT and bad. Doesn't really matter what kind, but they need it. Completely terrible when cooked to soft as well. Need some snap like ALL green veggies.

...for subs On other drivers it isn't about the amp, but the driver

How were they prepared? Both are easy to fuck up when cooking.

Not really. Budget wise sub amps running beyond 1ohm usually means wasted $$

None. Impedance is not efficiency btw

Try both and compare. I'd isolate only Left and only right and then together.

Auto anything on the 88prs was horseshit, can't imagine it being better. The one thing it should be able to measure is t/a though.

Stop worrying about the stage. That is the LAST thing I'd think about. Frequency response should always take precedence. Staging is going to be tough with those drivers in that spacing anyways. Getting a midrange that actually digs would help now. You treated the doors nicely, now they deserve some drivers that can put your efforts on the doors to use. Start flat. Play with all phase options 1st. Then start eq'ing out nasty peaks by lowering the eq at those areas. I like to acoustically measure t/a and correct, but that isn't trivial.

I was thinking about this, but 1.4 total is not big enough for what I'm wanting in a ported box. I've heard of people getting almost 2.5 cu. ft under the seat. ROFL. No way with your budget. 2cuft GROSS is tough without fiberglass AND will require a seat lift. With your budget you don't have room for 2 10's ported. 2 10's sealed, 1 10 ported, 1 12 sealed is pretty much it. Your measurements also won't help a builder since there is a big ass hump in the middle of your box and you are going to need to lift the seat. There is a simple reason you don't yet have an answer and it is all due to the way you've asked. Don't get upset at people who have answered no matter what they've said since you've given them nothing to go on. There are other constraints on underseat boxes besides dimensions as well. Have to worry about pole vent clearance, excursion clearance, and funny loading if you are firing towards a hard surface.

No way. Unless they are seving $500 entries. Typical net profit in food service is 10-12% So they're probably earning the $10/hr then. Not bad for a waitstaff position. If you scaled what I made hourly to a full time gig when I was in that position I would have been over $100k EASY. My old roomate cleared way more than that as well. If you can't average over 18% in tips you need a different gig as you suck at your job.

Have you sealed off the back wave yet? Building a box can be detrimental to a driver not really designed for it. 90% of car audio drivers were designed to run IB (at least ones that actually have a design). Putting that driver in an enclosure without measuring t/s parameters and determining what the enclosure should be could actually net you much worse midbass. The other problem you have is you are proposing lightweight materials. You need MASS to block a wave, not material.

Doing some consulting work today at the largest supplier of acoustic materials for automotive

Figures that 7th grade pre-pubescent activity stems from there. Just to clear things up. There is basically ZERO good information on SMD so take everything there as a nuthugger dipshit comment and move on.

Holy color choice

In a car you fine with 36 if chuffing is your concern.

I almost want it for my closet as well and that is the only reason why it is almost. Love those.