wutang512

could i get the acetone from walmart? I heard some people used denatured alcohol as well. But since I Wasted about $120 on this crap imma go ahead and order some tiles from SDS and do this right and not deal with this again.

same here... still waiting to hear from someone yeah i sent them a email about 4 days ago and have yet to get a response on prices or sizes

Well as far as front component tuning Im still learning about that. But subs you should have never went over 50hz for your subwoofer. I dont know anybody that plays their subwoofer at 80hz thats for midbass man. And you never ever set bass boost on your amp or deck on a subwoofer. When setting the gains for the sub you turn the subwoofer level on your deck all the way up then set the gains. that way if its too loud you can just turn it down. But remember no bass boost, no loudness on, and all Eq on flat or zeroed out.

Yeah definantly stay away from those flee market amps

Yeah definantly stay away from those flee market amps

you could go to madisound and look at some drivers and tweeters on there. Thats what i did

just please make them a yr from now. I just bought my BL a month a ago. I remember when I was about to by Q then bam! No more Q's cause the new ones were being tested and wouldnt be available for almost 3 months

Never heard anything back from you after I emailed you the shipping cost as you decided that you wanted a BTL if I recall correctly. We don't have any BTL's as the magnets are on backorder again until the end of July...we sell them faster then we can get them. Just off the BTL'S alone ya'll must be rollin in dough

really?? because at times i can get the sub pretty warm and stinky. this is when i beat the hell out of it. whats the deal with the pdx amps? i have it because i have a standard cab truck. the first generation versions have noise issues. Especially the 4-channel ones. at least thats what the guys over at diymobile were complaining about

Good job jake. Imma about to get my system rollin in the next 2 weeks. Ill have to stop by your house once everything is installed

damn is that from those san antonio pot holes?

And what would you reccomend in a $200 budget for both tweeters and midbasses

Depends on the frequency response on your tweeter snd your midbass driver If your using a dedicated 8 I wouldn't go higher than neccessary the higher you go the more directional the speaker becomes thats why door speakers generally handle midbass so it's placed in the stereo image, front, rear, left, right so the listener is unable to dicern direction thats basically what a bandpass does I have recording Eq's that'll bandpass with one unit I never done it in a car though but you could use a bass blocker at like 60 Hz and set your LP at your desired frequency I guess ill get a lil more specific then.... these peerless midbasses crossed from 80hz to about 400hz Peerless 830946 SLS 6.5" Woofer - 4 ohm from Madisound then these seas prestige tweet crossed at 3khz SEAS Prestige 27TFFNC/G (H1396) 1" Textile Dome Tweeter from Madisound what speaker is filling in the gap between 400 Hz and 3 kHZ? and thats the problem that comes into play I dont wanna have to cut my doors some more to add a midrange so what should i do?

Depends on the frequency response on your tweeter snd your midbass driver If your using a dedicated 8 I wouldn't go higher than neccessary the higher you go the more directional the speaker becomes thats why door speakers generally handle midbass so it's placed in the stereo image, front, rear, left, right so the listener is unable to dicern direction thats basically what a bandpass does I have recording Eq's that'll bandpass with one unit I never done it in a car though but you could use a bass blocker at like 60 Hz and set your LP at your desired frequency I guess ill get a lil more specific then.... these peerless midbasses crossed from 80hz to about 400hz Peerless 830946 SLS 6.5" Woofer - 4 ohm from Madisound then these seas prestige tweet crossed at 3khz SEAS Prestige 27TFFNC/G (H1396) 1" Textile Dome Tweeter from Madisound

chillin

Ok let me get this straight since im going active pretty soon with a 9887 and 100.4D Sundown For mid bass i would High pass on the Deck 80hz and up and then from my amp i should low pass 500hz and below thats basically bandpass correct? then for my tweeters just 3.5khz and up HighPass Am i doing this right?

If you didnt know 6th ave electronics is selling the Alpine 9887 for about $230

with all that? hell naw unless you wanna get one from japan. I know pioneer carrozzeria , kenwood japan, and alpine would have all them features but not for no $450. More like $2000 or more. Your not gonna find anything like that in america cause majority of us are too cheap.

And Bandpass does require a 4 channel amp with a Subsonic filter Correct? Bandpassing your mids will be done completely in the 9887. The SSF is ONLY for your subwoofer, but with the LP of the headunit and the SSF your sub will be bandpassed as well. When I get the amp and deck Ill come back to this thread and ask how to set it up correctly. Im trying to work a crazy amount of overtime

yeah i definantly want the D revision then

I think i seen that one its the C revision. whats the difference between the C and D revisions

you dont think sundown will revise the 100.4D Any time soon?

I seen DB-r has them for $290 Refurb and When I think about it ill only be paying $100 for it since i sold my inifinity amp for $130 and opened a chase account with a coupon which they gave me a extra $100. Might as well get it. Ive seen everybody else around here with sundown products and have heard no complaints

Hmmm.... Explain more please Ive been searching for about the past hr a 4-channel amp 100watts or more at 4 ohms with a subsonic filter without going over $250 used or brand new

And Bandpass does require a 4 channel amp with a Subsonic filter Correct?