holley2346

Wonder if they will be happy with ~500 haha... no but seriously I was just asking because I have an older 2 channel kicker amp they will be running off of. I HOPE it puts out enough for the subs and I HOPE it will be stable @ 1ohm... I know it isn't stable @ .50... I think it's ~300 watts I don't even remember... it's currently running kicker comps so hopefully there will be an increase in sound Jesus I need a job.... Fi takes all my money Someone buy my 12's PLEASE

Payment sent I just couldn't say no.... I guess I will end up putting these in a sealed enclosure in my boat. What is the rms wattage? One site said 300, and a user said 250..... wish they were dual 2 ohm.

How much for 2 or 4 shipped to 36022?

I ordered yesterday... paypal says that the payment is completed. I was mostly referring to how long the tooling would take.... how long till it gets in UPS hands... Also, I would email but i never get responses. I sold my 18 inch bl's, is it possible to pay for FI car audio to send me standard fi bl 18 boxes with the padding and everything they use so that I can ship it to the buyer using those boxes? I want it done correctly.....

....

I can say that you will not be disappointed with the bl's at ALL. Especially with that amp

Can I trade a bl 12 for 2 or more of these? It has never been used

2 BTL 18'S + 2 SA3000D'S

Not to jack this thread... but I just read my 18's because I am about to ship them out to seller. They were ~1.2... it was the same way on my 12's though so I guess this is normal? Also when leaving the leads connected and pushing the cone down the level bounces around dramatically.

Wondering why my thread for the sale of my bl 12's was locked and closed? I abided by the posting rules. ??

Alrighty... it got moved back and unlocked.

I am going to redo my truck..... I was tired of not having space in the back of my truck. Therefore I decided to go with 1 BTL 18. Using same amp/electrical/etc. Here are pictures of the pull out.... All of them lined up

Hey.... I recently sold my BL 18'S and want to either go with a BTL 18 or an re xxx 18. I am wondering which would be better in my application..... mainly spl oriented set up to be used daily. I must say I loved my bl's and don't know much about RE subs. Thanks

BTL it is... thanks Just ordered so hopefully it will be here soon.

Due to the need for space in the back of my truck, I am forced to downsize. Currently I have 2 fi bl 18's installed. What should I do? [scenario 1] I have 2 fi bl 12's that I purchased along with the 18's and haven't touched them yet. So I would just make a box for them and put it in. [scenario 2] I would remove 1 18 and build a new box [scenario 3] I would sell both of my 18 inch bl's and buy a single 18 inch BTL and use it. Which way would be the loudest? Subs up, port back. Sundown audio 3kd. So the main question would be, will I still get the lows with 12's that I get with 18's? And would an 18 inch BTL be louder than 2 12 inch BL's? Help is appreciated

I am considering 2 btl 12's at .5 as well. Which way is the best route to go, I vote to hear from bigjon. I just want lowwwww and I don't want a lot of space taken up. I wouldn't want just 1 bl, that would be a waste of a 3kd.( 5 cubic feet is low compared to existing. )

It would be the minimum 5 ft ^3 I am currently stuck with a 12 foot ^3 box.

I say just lay it down with some cheap fans blowing air through. Looks neater that way and seems as though it would perform better.

Into a terminal in the sub? You don't have to do two..... Into the amp outputs? I used 4 gauge for my speaker wire and I used distribution blocks.

I have been too scared to even start on removing my door panels to complete my install and put in some mid bass drivers / tweets. I was wondering if anyone had any experience with 07 / 08 tahoes / avalanches and knew the right way to take the door panels / pillars out without breaking anything. After searching around for a while I couldn't find anything. I really don't want to mess it up too much.... it's basically brand new. (like 18's won't vibrate it apart anyway)..... Any help would be appreciated.

Scored a 148.6

Thank you very much, I honestly searched around google for a good 30 minutes or so and found some stuff. But it wasn't anything that was of much help to me. Thanks

doesn't know that I paid in cash. =]

Took some covers off looking for screws... was able to find 0. There is no obvious way to take them off... also tried a small bit of prying to no result.

Has an animated gif avatar.