bass_4_ever

I messaged BeeJay25 on youtube, the guy playing the 4 Warden's off of the 2 Stetsom 14K amps. He said the Stetsom plays great with music and that he hasn't had any problems playing music.

hey everybody, I was just wondering if people on this board have used them before...any feedback, pros/cons about these subs? I will be using them ~30hz, mostly musical (daily use) and some competitions. Just would like some hands on info about them... Thanks, Andrew

anyone else have any info on Stetsom amps?

So...Stetsom amps arent made you play music?? I was thinking of getting the 5K2D (1 Ohm) to run 2 AA Mayhems...

X2 , what are you expecting to get out of the sub? what do you want to accomplish? what are you going to be pairing it with? etc etc

yes, the one that is not working now is the one thats on the distro block

I have 2 Massive Audio D3000.1's right now with the gain turned up about half way. I put a recommended 100amp fuse in the holder... today i got in the car, turned on the stereo and one amp didn't turn on. I checked all the wiring, everything is fine...checked the fuse, fuse was fine. The amp doesnt turn on at all, doesnt go into protect, nothing. I used a multi meter to check the voltage, the remote wire was reading 12v but the power wire is reading 0.03v what happened?? :S

Like I said, I'll check everything tomorrow at lunch and i'll report back by the end of the day...I'll let you know how it goes! and yes I'll turn the gains down to 37v!!

I will check more tomorrow during my lunch and I'll fill you in! Thanks for the chart, it will come in handy! and Ken, I added you on msn, hope thats alright I'll call MA tomorrow and talk to them about they're fuse ratings... why would one amp pop and the other one doesnt? they both have the 100 amp fuses...

It has nothing to do with the voltage your putting out the rca's, you have a power problem somewhere within your setup. Personally I think your amp will need more fusing than what you are using. what do you mean by "Personally I think you amp will need more fusing than what you are using." ?

haha yes mom. I'll try the power/grounds tomorrow at lunch and report back.... and just out of curiocity, how did you figure out 37v AC?

I dont understand though...at first the amp was set very low and my subs were barely moving...I turned it up on both amps to a little under half, and this happens.... lol

how would I have pushed the amp that hard? I mean, the ouput RCA's from the Alpine is only 4v....

RCA's could be put into an EQ from the deck then out to the amps lol and now what the hell lol

yes, the input on the amps comes from an Alpine 9886, yes the RCA's... and would it make more sense if the decimal place was moved over so its 6v?

my input is directly from an Alpine 9886

so how would i stop "over current" ?

lol thats wat was on the meter...60.5. Theres no way that 2700watts is coming out of those amps lol, at half gain....

1.33, each amp is running 3 10" subs

i dont remember what i set them to, i believe i used just the gains, no bass boost...set them around half way up, 60.5

i try to get 20-40hz tuned all the same... 30-40hz was tuned the same which is what my stereo peaks at. im not sure what you mean by 37v ac...

depends on which tone, each tone gives a different signal....the multi meter is places on the speaker outputs of the amp and set accordingly on both amps

both amps are set using a multi meter, set to the exact same output signal

not sure, but like i said, it says 100 amp fuse recommended in the manual, and I've also called Massive Audio and they said 100amp fuse is enough. i think its 104.16 amps or something... but im not running 1500wrms out of the amps, they're only turned up about half way

correct.