NDMstang65

Build and test...that's the only way you are going to get loud. There simply isn't a 'ready mix' you are automatically loud box for every scenario...

Don't work on the weekends and Scott has been out of town... XXX 12 kits are $95 + shipping each (12-15 dollars depending on where you are located.) Thanks! Nick

Works fine for me..

It's back up.

That is STRICTLY home theater. It will not work for car audio.

Constantly doing new stuff.. In our true form we only show something when we are ready to.

We still make the kits. The web guy must have taken the 15's down by mistake while we were making some adjustments. I'll work on getting it back up today hopefully..if the coding isn't messed up that is. Thanks! Nick

Not much we can do to help..if you want to know what is "Loudest" you have to figure that one out on your own..as every single vehicle is different. It's sort of asking John Force how to run the fastest quarter mile time...there are 2 million variables...he simply can't tell you how to do it. That is why we have the ranges to stay within..if you stay there, you are fine. -Nick

It'l go out Monday or Tuesday.

Had to make some coding adjustments because it wasn't working out right with shipping etc. It'l be back up on Monday or Tuesday when the web guy gets it finished.

Answer these questions If it is a warranty issue..we'll definitely get it taken care of. I need to know this information. PS, You don't need to 'break in' your subs. They'll do that with father time at the reins.

BL's don't have pole vents...you can sit the back plate on the back of the box if you want. Thanks! Nick

The BL's would be louder than the single BTL, provided you have the room.

Need to know what kind of box they are/were in, all the specs to it, tuning frequency, size, how they are firing, how they are wired, settings on the amplifier etc. Speakers are simply dumb..they don't blow themselves for no good reason Thanks! Nick

Honestly you shouldn't need any more then 1000 watts.. That 1500 is a bit too strong and wont leave much margin for error if you are hard on stuff. Thanks! Nick

You must solder them... If you have our new integrated tinsels you need to pull them through the tinsel block and solder the top side, snip the bottom off and run a bead of solder over the bottom as well.

When we're ready to say, everybody will know

Give us a call here at the shop. Ascendant Audio 5450 Cameron St #104 Las Vegas NV 89118 Dealer Phone: (702)379-4371 Dealer Fax: (866)795-9972 [email protected] Tech/Sales Phone: (702)476-8587 [email protected] [email protected] Shoot me an email as well [email protected] We'll get ya taken care of!

There is no warranty... The Kicker amps have one major flaw as they do not have a adjustable subsonic filter. I believe it is set at 25Hz @ 12dB per octave which is a very low shallow slope for a SSF. Your enclosure would have to be tuned 30Hz or lower for it to be effective.. What you saw happen was the toll of time of abuse of not having a proper subsonic filter / tuning of the enclosure for the amp. No sub will take that if it is any sort of high excursion woofer or anything that has a long coil that is designed to move more then say 25mm. You can definitely send it in for a recone and we can get you back running again no problem, but if you are planning on flopping another speaker in that same box with that same amp it simply isn't going to last. Thanks! Nick

Measure your trunk and see how much room you have to work with, then figure out what kind of budget you have to work with for subs/amp(s) wire etc. and go from there! Thanks! Nick

Just have to make sure your settings are all correct and set up properly.. If they are not set up properly you will break the sub. Thanks! Nick

Yep Mix it up and dab it on the spider landing and surround landing then put the gasket back around the edge of the surround and push it downwards a little to assure that it has adheared all the way around the basket.

Yep back to normal.

Ladies/Gents, We're looking at a 3 week wait currently with the BTL's. I've had numerous emails of people asking "Where is my BTL" and somehow they missed the flashing red letters on the website that says "Current lead time as of x/x/xx is 3 weeks" So..here's a picture. This means that it will be 3 weeks before we get magnets in. Then additional build/ship time for your speakers. If you order now, you get free cooling and a T-shirt with your order for being patient and waiting. Thanks! Nick

probably