yenwen

Not in your area but they will get the job done right! http://www.db-r.com/ Yea he posted on CA forum that he's packed and doesn't have time to work on it. I need to find an alternative. really hoping to find a local guy

I have a PPI pc1800.2 that burned out. I haven't opened it yet to see what fried but it's definitely dead. I was wondering if anyone knew of a place down in Glendale or LA or even OC that knows where I can get it repaired? It's a sexy amp and I'm not willing to let it go.

Yes I plan on taking that P.O.S. out too. My cap is total garbage

Thanks for your help but I think I found out why my fuse kept blowing. I rewired my sub to 4ohm and it seems to be doing just fine. I will probably switch out to a 120 amp ANL fuse just because ANL fuse would be more reliable and my wiring will allow it.

OK so I checked and I'm running 4gauge but there are these 8gauge wires I think that's hooked up to my Cap. I think another problem is that I have my sub wired at 1ohm and my amp is 4ohm

how do i test that? Plus I might need to run new wire. A friend of mine says I actually have 8 gauge. I'm pulling 800watts. I've blown 100amp AGU in less than 2 minutes

Whenever I'm blasting my sub my fuse will blow in less than a minute. I'm running 80amp AGU fuse with 4 gauge wires and a PPI 2200 amp. What could cause this? Is there anyway I can fix this problem? I'm not sure but I think my ground wire is a 8 gauge. Oh and I'm looking to have someone build a custom box for me that involves bending plexi glass.

See I know it's not worth doing if I send it to JL but would it be worth it if I could get FI soft parts?

I have a 12w3v2 with a blown coil. Is it worth reconing? or can I just do it for fun? Who and where or what can I use to recone it?

Man those look fantastic! I'm debating if I should get the BM or get the SD-1 hahaha there is a huge price difference. But I'm interested in the BM since it's a good sub and the SD-1 cuz of the absolutely great price.

Like I said before not doing anything crazy I just want them to be in factory location. I didn't understand half the stuff you were talking about in the last cabin speaker thread I started. If you wouldn't mind explaining more that would be really helpful for me. This has been really great I've been learning so much. I think for my sub-stage I'm going to run an FI Q in a ported box. The box will be custom made for the sub so no worries there. Amp is still going to be the ppi pcx 800watts rms at 4ohms.

I've been checking out the BSW speaker upgrade for my car. pricey but they use rainbow dream line. what do you guys think?

What are mid range? The car has a 3 way system 5 1/4'' in the kick panels, i think what looks like 2'' or 2 1/2'' in the doors along with like a 1'' tweet so which one is mid range? I know for a fact that i hate metal dome tweets too sharp and cold. I like my music to be warm and smooth. been going around to best buys, circuit city, and those places to check out speakers... not that i'm proud of that but it's kinda hard to get a meet going on DIYMA. They want to do it on Oct 20. I want to hear some stuff before then. Any suggestions that'll at least point me in the right direction?

Ok, if I have to have more power to have a loud sub and apparently 1500-2000watts is going to be what I need to have a good woofer. What's a good budget amp? or just a good performing amp. Like I said earlier I want to maintain the same quality as the PPI PCX that I currently have.

Well I wasn't looking to port 2 12's was looking to port a single 12 or 2 10's if it's not possible to do two 10's ported since i'm leaning towards two 10's unless i can get a 12 mag d2.