KyleBrown

Why?

I'm assuming D1 subs? the BC3500 is rated for [email protected] fyi If you want a gain, get your batts and buy a second AQ2200.

Looking good man! I won't lie, I'm really happy with my BC3500's!

nice start!

He most likely won't get any lol

Personally, I' rather have a matching batt bank.

Nice new toys. I don't think I'll be able to make bassbattles. I think I'll be doing a real super stock build.

It's getting there

nice work man

Need to clean my car bad

Looks good, I like the new clock.

I wouldn't say top of the line, being that an N3 will run you more money and be louder. If the OP wanted to, he could get the SPL coils for the SAs Thermal will be pretty much equal. The weight of the 15" cone should help with the subs being peaky.

No idea when I'll get amps from IA and I needed more power for turkey drags next month. They're old beat to shit atomic 3 ways. About to go make a video I think.

Flip a coin. A lot will come down to the build.

Good deal, SCT is good shit

Well after lots of back and forth, finally did the trade for two BC3500's. Got the amps, showed up without bass knobs and in what I would consider highly used to rough, not minty. I'm quite particular about my amps though. More back and forth and some money coming back to me and getting a bass knob sent out(not going to use it but it helps with resale) Other than all that crap, I'm quite happy with the power increase. Bottomed the subs out on bass I love you lol, not too bad though. First time I really romped on it, my rearview mirror broke off and took some windshield with it. Only 6 days old at the time lol. On to pics poor packing I fixed this already It's about an 1/8 thick junk. I know I need to find another RCA. Just super busy and it's a low voltage signal.

you are correct sir, I can't wait to see some NSv3 or Zv4's in there.

4 Zv3 15's and 4 Saz3500's @.5

Yea the new stuff seems a lot better.

So I finally ordered some 80mil AT deadener to test out. Shipping was quick and I received a discounted rate. So that was great. Everything started going wrong once the package showed up. The adhesive backing on the foil had gotten smeared all over the inside the box, so I had to literally rip the box apart to get to the deadener. The adhesive had gotten stuck all over the wrong side of the back as well. First thing I noticed was the foil is a extremely rigid. It is close to the same thickness as stinger roadkill expert, but much less flexible. Second, is the plastic film to cover the adhesive is difficult to remove, which leaves more opportunities to be slice by the aluminum backing. Third, the peanut butter colored adhesive is excessively sticky and too "gumy". It has the consistency of chewed up bubble gum. But I figured this would make it stick better.... Wrong... The area I applied this deadener was the underside of my rear deck. I have previously used stinger roadkill expert and second skin damp pro on this area. Each time, all deadener was removed and the area prepped again. The stinger and second skin where on there about 6 months each. No issues at all. I got done cleaning all the second skin off, prepped the area using acetone and then a damp cloth. Ensured the area was completely dry, then began the application of the Audio technix. This was an over timely process due to the lack of cooperation from the aluminum backing and the gumy adhesive. I do not use a roller, I use the handle end of a screw driver. It allows me to apply more pressure and get in all the cracks. It takes longer, but is more effective. Ok job done right? WRONG lol. I pop my trunk a few days later and notice the some of the deadener drooping down. So I take the time and reform the deadener. About a week later, I pop the trunk and find a bigger piece of the deadener laying on one of my amps, and the adhesive literally dripping down off the rear deck. I've since ripped all of the crap out. Now I have dripping gumy glue sheet all over my rear deck. I tried some tips from other to remove it with no luck. Its a complete catastrophe. I've asked to send the unused portion back(20ft) a get a refund, but I got a no. HERE ARE THE PICTURES, KEEP IN MIND, THE DAMP PRO AND ROADKILL EXPERT WHERE APPLIED IN THE EXACT SAME FASHION AND THE EXACT SAME AREAS. Now if you come in here talkin trash, keep in mind, I've used alot of deadener and adhesive for this crap can't even sustain itself, so there's no way it will hold up and aluminum backing. Also the over thickness is less than that of damp pro and roadkill expert. I'd rather pay the premium over priced price of dynamat extreme than deal with this. Damp pro, roadkill expert, and dynamat extreme are superior products. the two larger pieces had been off less than day in those pics the smaller pieces were removed at that time, then pictures of the adhesive dripping off the following day.

Looks good man, congrats

IDGAF the new softparts for sundown are badass. I'm not sold on them being able to meter louder, but I understand the theory. I'm sure they'll be great down low though. Will this be ready for Turkey drags?

Went through the thread... Waste of time...

its definitely getting there!

biggest reinforced cased batt from xs is the D6500, so that would be my choice. The D3100 is not reinforced. It's suggested to use heat wrap if you put one of those under the hood. don't mix