pimpdaddy1787

What does everyone think of a denon DCT-1? I know a friend who has one that i might be able to snag cheap!

So since I am going to be finally putting in the saz2500d, I figured it was time to put new subs in! But the question is which ones. I like the zcon's and they can handle 2500 each. But the sundowns can handle 1500. My box is 4.75^3 tuned to 36hz. Finally got money to get the d3100 and. Already have the 0gauge to wire it. Any suggestions?

And I think ima go with the z's. I wanna be able to pound the crap outta them and not worry about being close to the tippy tip top. Lol. I can change port if needed. Need to redo front of box anyway, starting to come apart.

Ok, so I come up with 79, which whe multiplied by 21(length of port) I assume, I come up with 1659. Sound rite?

So back to my original post! Lol. How do I measure port area on a trapezoid port?

I don't buy the 100% either. Power in = power out. You have to charge the cap, then it discharges. But along the way ther has to be some power loss and distortion somewhere due to heat, thermal dynamics, wire resistance, circuit board resistance? How can it be over 100% efficient?

$25k to be exact. And only 18 ever made. Steve Meade has 4 so that leaves 12 left in the world!

Battery I don't know, I know Meade916, Steve Meade on you tube has 8 d3100's powering 2(two) t15k's and that is ferocious. 4 alts from mechman, the 370 amp versions, 8 50 foot rolls of 0 gauge just for the alts and amp. Wtf. A warhorse from kicker would seem more logical

So how would I figure out the port are on a trapezoid style port?

Not going with 15". Don't know where that came from. Lol. Goin with 2 12's. Port is 21" long and 18.5 wide at top. 20" wide at bottom. Basically same size as bottom 4" of box and 21" long. Budget is not really an issue as I do a lot of ebayin and keep money in my PayPal account for my stereo needs! thanks for all the help

Box was actually designed for 2 cvx122 kickers, which really do hit hard. But I want more and have the amp and electrical to do it so why not? Specs seem to be ok for the z's but wanted to double check before dropping $900 on a set of subs that will need a new box

Sorry bout the lack of info. The box is 44" wide x 18" tall with the 14" top and 21" bottom. Both subs (12's) on top near left side. Port is on rt lower. 4" tall from bottom and I think it 21" long. Have to double check if needed. Had Ryan @ ramdesigns design it for me. I'm looking to break things not necessarily hear them real good if y'all know what I mean. Lol.

Anybody know anything about a sundown/T3 hybrid 12", dual 1 ohm? I'm lookin into them but haven't heard anything about them. Supposedly 2500 rms? Would they go good with a saz2500d and a 4.75 cube box tuned to 36hz?

here are some pics

ok, my s10 3 door has the ram designed box now only problem is the box comes to 3" below the back window. and takes up the whole extra cab. 4.75 cubes. my idea for mounting the 2500d are now limited. can it be mounted upside down? i was thinking of building/welding brackets across roof and mounting upside down. any ideas are helpful

I will take some pics tonite. As far as the floor, that's out. Box sits on floor. Built to go from back of seat to back of cab. My seat literally rests against box. Trapezoid style. There is 6" of room from end of box to side of cab. There is no room in front. The 45 I kind of like and that was recommended by someone else also. What should the rack be made out of? Can i use some of the extra mdf i have, then wrap it? Under the seats is not an option also. I have cut and rewelded the frames to get the seats lower. 2" of room max and floor is not straight. It has ridges built in for structural support.

i wasnt goin to direct mount, rather a "bridge" welded between both b&c posts that spans across roof. then build rack for amp that has enough room to put 2 small fans for air movement. that way i can run wires inside the posts and they will be hidden. but question was can it be mounted upside down? i would think so being as its a solid state device, but just not sure

Ok, so I went to ram designs and had Ryan lay out me a box. Built it this weekend and installed it. Still have not been able to run the 0 gauge for the sundown so I am still using the zx500.1. WOW. What a huge difference. Even as far as the distorting sounding. The amp is o-scoped so I know it's not clipping, but rather "distorting" if that's the correct term. Now it really really hits hard. Lots of kudos to Ryan for the design and also a big thanks to ricksi30 and stefanhinote for sendin me to ram-designs. I can't be more pleased except when I get to install the sundown

Well, i think its time for a custom box. The current box was made for 2 12" w7's. my speakers are 10cvx122 kickers. specs are min port, 1.75+port and max 2.25+port with the port being 63" sq x 20" long. figure that out. 87.32 spl, 3.74 Revc, .0507 Sd M, 18.62 BL TM, 57.98 Vas liters, 28.44 Fs Hz, 197.28 Mms Grams, 10.209 Qms, .38 Qes, .3665 Qts, 15.4mm XMax. whatever all that means, lol. The max dimensions in the truck are ______14____ and about 4' wide maxx. / l / l 1-1.5' / l /______18_____l Also have another question, are they ok to fire sideways? was told by others not to fire sideways as this will make voice coils rub. I kinda would like to make them fire up for asthetic reasons, looks better but whatever works. I am gonna push them with a saz2500d, 2 d3100's, lot and lot of 0-gauge, and a 220 amp powermaxx alt. Any help would be greatly appreciated, as far as building it. I have my trusty neighbour. he builds all of his own furniture and said this would be no problem as long as we can get some dimensions, and my money, lol like i said, any help greatly appreciated and all i wanna do is bump really hard!

True. I thought I was gonna have a problem out of him, but after I told him what I did and what I found, he had no problem takin it back

Funny I run across this thread. I purchased a power max from eBay also. Supposedly 220 amp at 1700rpm. HA. At idle stock alt. would do lvl 28 on Pink Floyd and when I installed the powermax I could only go to 25. What a joke. Cheap made! Took it to work and clamped an amp clamp on it and put a 450 amp load on batt. Max output was 130 amps. I have big 3 done in all 1/0 wire so resistance was not a problem. No where near stated amperage. Voltage fluctuated so badly I emailed him. His response was funny. I sent it back and now have a beastly mechman 270 amp with no problem at all!!!! Don't waste your time or money with powermax, get a mechman. Someone stated in a post earlier I saw that was so true. "you get what you pay for".

Hello everyone. I am from southern maryland and love working on my truck. I work for a G.M. dealer so working on electrical and fixing vehicles (at work or home) is my thing. I love bumpin down the road and in my spare time i have a gas r/c boat i play with being as i also live on the water. My current project is my daily driver, a '98 s10 3 door. Currently it has 2 12" kicker cvx's, kicker zx500 amp (underpowered i know) and a kenwood headunit that is fully compatible with my Iphone. I have in my garage a saz2500 that is going in this month along with a powermaxx 220 amp alternator and some new batts (2). just have to get all the wire and connectors and fuses. Anywayz, enuff of me.. WUZZUP......

yea, after debating it for all of 2 minutes, i'm going to send it back and get a mechman. they have a 270 amp for my truck. cant wait for it to come.....

so my question is, what size alternator should i need. i have 2 cvx122 kickers running off a saz2500d running at 2 ohms, custom ram-designs box, (which by the way is sweet and well worth the money ) 2 runs of 0gauge pos, 1 run of 0gauge neg, big 3, 1 d3100. its a 98 s10 4.3 x motor(hi output). i bought a 220 powermaxx but unsure if this is enuff. Any way to calculate if i need more or another batt?

Thanks. Didn't realize the section I was in till it was too late and sorry for the double post.