sundownz

I used 60 Hz as we are powering woofers and in the box they are in the impedance rise is fairly predictable at right around 200% As for THD -- I'm not measuring that in this test. Just checking to see how much power it can generate when loaded down on a real load -- WELL in excess of the rated power so I am quite comfortable that the power with THD ratings from my build house are indeed accurate. Also to keep in mind... we had only 4 awg wire going to the amp on the bench. Just as a quick test I unloaded two channels and the remaining pair output right at 1000 watts. I imagine I could get close to 1kw per side still loaded down on all four channels with the proper 1/0 wire going into the amp as voltage drop going into the 11s when testing on the 4 awg.

... well almost. Originally posted by Greg Kashin on my SMD Forum : Is the Prime Minister of The Russian Federation also a member of Team Sundown??? - SMD Forum ----- Yes, Vladimir Putin, the current Prime Minister and previously The President of Russia for two consecutive terms was at a bike run and was THIS close to rocking Sundown Audio :yahoo: Putin is wheeling the leading trike alongside of him is Surgeon a notorious Russian biker and leader of the Night Wolves.... right behind them is a huge trike rocking two Sundown SA-10's ...I know it's a little hard to see in the vid ( look closely at the vid from 0:18 to 0:21 ) and the media pics but them is Sundowns for sure and they got em here Sundown FTW!!! Путин на байк-шоу под Сева�тополем: Хай живе байк! (видео) -----

Yes, we have sold 100s of SA series woofers in Russia through our distributor there Quite a few amps and Z v.2 over there as well. We are shipping the first four NS v.2s soon... four 18s!

I don't have specs on hand for all the various spider configurations.

It hasn't gotten warm yet -- I am sure it will, though... but it does have a fan (which is VERY quiet).

Little bit of clamping : All channels LOADED for the test @ 1 ohm per (2 ohms bridged on the clamped channels) -- 60 Hz tone played. Bridged channels 1 + 2 clamped. 820 Watts 62 V 13.2 A @ 4.7 ohms So 410 per channel @ 2.35 ohms We didn't measure voltage but based on other testing it should be dropping to the high 11s to low 12s. It certainly exceeds expectations

Loaded down to 1 ohm per channel doing some testing.

All of our subs are designed around small boxes -- the SA-12s like about 1.5 cube the 10s more like 1 cube ported. Cut either one in half +/- 25% for sealed.

A little revision here... If you are going to beat the daylights out of your sub *constantly* do not, for any reason, use more than 0.5-0.6 cubes for it at any power level. The original recommendations are assuming that some care is taken to monitor mechanical stress of the driver.

Unless the SQ competition format changes I'm not that interested to be honest. When you can win a "Sound Quality" competition by having more screws turned the same way than the other guy... it ceases to be a "Sound Quality" competition.

Just a little tip - it may be easier to buy a new frame than try to get the bolt down ring off the SA-8 frame on the new ones. I do have frames in stock for them. Plus side... the spider will NOT be coming off any time soon if you don't want it to. Here is one we removed this morning : As you can imagine it didn't come off easily. It is glued under the spiders, bolted through the frame, and epoxied on top.

Damn David - use some screws next time *laughs* JK - looks real loud.

This one uses a traditional paper cone... it's more of a test bed for ideas. May never even make it But it's cool enough that I wanted to share pictures.

I'm trying out several ideas for the Neo 8... this one is TOTALLY different from the other one... this one is overhung, huge motor, solid core, 2.5" coil, giant shorting ring, etc. The other is XBL^2, compact motor, vented core, 3" coil, smaller shorting rings, etc.

Each pair of 1500s is strapped on 3 subs.

... and SA-8 bolt down ring. Truck showed up late today * SA-8 and mystery prototype in background being tested. * Ohhh, nice looking magnet boot ! * Screws for bolt down ring * Just to make sure... the ring was also epoxied in. * SA-12 with magnet boot

We tooled up a steel ring that holds the spider on the SA-8 down -- it is bolted in from the back and then epoxied in on the front... there is ALSO glue under the spider. So I don't think it's going anywhere now

I will add that no cost was passed on to the end user for either the bolt down ring OR the magnet boots

Hey guy - my shipping company gave me unusually good news for once My SA-8s / 12s weren't due in Charlotte until the 25th but it seems they should be at my door tomorrow after 1:00 at some point. Unless something weird happens, of course !

They won't come back out of protect unless they are turn off and back on -- so they aren't popping into protect. Seems as if you are losing signal -- try another output on your HU.

3-4 months is my estimate -- if someone wanted to get custom coils made technically the SA-8 basket, cone, and spider could be used... a bit stiff for the E8 motor but would indeed work.

Yah, that is correct... all the ratings are very conservative to the point where they are still met at 12.8 volts.