Hzd Skizzy

D3400 and charger still for sale.

S3400 sold

Yes!

Bump

Pmed

New Deal! Batteries are expensive to ship! I will now pay for half of the shipping price on batteries! Intellicharger lowered to $150 shipped!

Prices Lowered! Xcon #1-$300 shipped and paypaled Xcon #2-$280 shipped and paypaled Both Xcons-$515 shipped and paypaled No Thanks

Yes both still available

Pmed

Bump! All 3 still available!

Bump!

Both are still available!

I like it! What are your plans with it?

Here are the updated resting voltages of the batteries, I let them sit for about a day and a half just to show that they don't have any dead cells. S3400 D3400

Thank you! No! You're fine, thanks for helping me out!

Bought his Rockford Fosgate t1000-1bdcp. It was packed well, it works very well, and it looks good. Lost is a good seller, good communication, would do business again. Thanks!

Well, according to percentage of paypal fees it would come out to me requesting $499.79. I will personally not be charging handling fees, that term was to be taken lightly in the sense that whatever UPS charges for shipping and handling is what the buyer will pay. To avoid any "vague" perceptions I will edit my post and delete the term "handling" to avoid confusion. Sorry for the confusion, hope that answers your question.

I apologize but due to some unforeseen circumstances I am no longer able to accept trades, I am in need of cash at the moment. Since I need the cash, I am almost forced to lower the price of these solely to move them. Do take advantage of this crazy deal, because the price may not stay for long at all. Price for BOTH XCONS: $485 plus shipping and paypal fees!! **Edited to omit the term "handling" to avoid further confusion**

I'm going to have to gather my thoughts on the SP4 motor, will let you know.

Not really anything specific, but feel free to surprise me

The ways I see it happening are either using distribution blocks with 1/0 inputs and outputs, for example this one...http://www.sonicelectronix.com/item_15889_StreetWires-DBX30.html you can put 2 runs in it and 2 runs out. Also, I had no choice but to route my runs outside the cab. There was little to no room inside the cab to put 4 runs of 1/0. Without bolting it on the truck I used plenty and plenty of zip ties. To get it back in the cab there was just this convenient grommeted hole under the carpet. I cut the center grommet out and got all 4 through. Just make sure you don't try and stuff your wires through an opening that doesn't have anything separating wire from metal. Metal will cut the wire and it may cause an accidental ground from a positive wire.

Bumps

The type of response you get will be related to the port tuning, and sufficient port area. When I attempted to make enclosures, I used Torres Box Calculator. http://torres-box-tuning-calculator.software.informer.com/ *Edit* Also, if you're not confident in yourself making your own calculations and or designs, for a small fee, most of these custom fabricators will make a design for you with cut-sheet dimensions. All you need to do is create the design using the specifications they gave you.

Could be a silly question, but is the rms rating still the same as a normal GCON?

No I didn't disconnect the battery. Would there be any other signs of a blown pico fuse? You may have hit the nail on the head.The issue is fixed. I pulled out the paneling in the back where the rcas run through and when the seat is in the upright position, the post was pinching hard on the RCA cord. The cord must've rolled itself under the post when I pulled the amp out to tune. I pulled the rcas out and re-routed them a better way where they wouldn't be pinched. Have driven a good bit today after doing that, and no more whine. Thanks guys for helping me out. I would like to know other signs of a blown pico fuse, because if I did blow it, I'd like to go ahead and replace it.