sefugi

spaghetti, looks like an all you can eat buffet! I'm sure you've got it covered. Yep, it's a feast for two!! So far so good on having it covered.

Now for some info on the wiring. Since this motor will be old school HEI and Carb all the computerized wiring needs to be removed and quite a few circuits will have to be rewired. From the factory the fuel pump, A/C, and the starter relay were controled by the computer, now they will operate by the key in the way of some added relays. First line of bussiness is to trim out the wires not needed and get a layout of what and were we need to make adjustments. Here are a few pics to give you an idea what we are up against. By grasshoper at 2010-11-01 By grasshoper at 2010-11-01 Harness under the knife... By grasshoper at 2010-11-01 By grasshoper at 2010-11-01 An idea what was removed from the original harness By grasshoper at 2010-11-01 By grasshoper at 2010-11-01 A portion of the schematics needed to trace all the circuits. By grasshoper at 2010-11-01 Will be working to get the harness setup for the new motor and the few extra cicuits we will be adding.

Thanks!!!! Need some sauce to go with this spaghetti of wiring...

and again!!! Us Dads can be cool guys sometimes...

i love the discreet post edit. no problem though man, i really appreciate the help. plus when it comes to what i'm doing, it won't be for competing etc. so anything close enough is no problem. Sorry, did not take into consideration for the common port walls, went back and checked and that made the difference. Again, sorry for the fail.

With the .15 disp. I come up with 2.25 @ 31.4--Looks like you are about were you wanted to be. Of coarse I am no box designer, but I can plug in #'s like a mad-man.

Lot of really nice cars there!!!

With the demensions you gave I come up with 2.4cu' net vol. tuned at 30.4-- of coarse you did not say what sub or the displacement so after you subtract that the net and tuning will change a little. Hope that helps.

I like the kerf, hope to do one myself one of these days. Thanks for the consistent inspiration!!

Grasshopper has been held with his job making that money to continue with his build so I'll bring you up to speed with what has been happening. This is the Hal-effect Sensor for the new Speedo we will be installing. We have soldered in a harness to run from the trans to the firewall were it will be tied in as we get the wiring setup. By grasshoper at 2010-10-27 Here is the starter ready to be installed with the feed and signal wire setup. By grasshoper at 2010-10-27 Have completed the plumbing for the cooling system. Heater hoses installed. By grasshoper at 2010-10-27 By grasshoper at 2010-10-27 Check out that high-speed radiator cap!! By grasshoper at 2010-10-27 Lower radiator hose installed. By grasshoper at 2010-10-27 Upper hose installed. By grasshoper at 2010-10-27 By grasshoper at 2010-10-27 Secured the trans. lines. By grasshoper at 2010-10-27 By grasshoper at 2010-10-27 Cleaned up the wiring going to the fan module. By grasshoper at 2010-10-27 Got the accumulator and A/C lines installed. By grasshoper at 2010-10-27 By grasshoper at 2010-10-27 Here are just some random shots that we took along the way. By grasshoper at 2010-10-27 By grasshoper at 2010-10-27 By grasshoper at 2010-10-27 By grasshoper at 2010-10-27 By grasshoper at 2010-10-27 By grasshoper at 2010-10-27 We have split open the wiring harness and have started the process of eliminating the wiring not needed in our situation of this build. Will get some pictures up of the wiring in the next few days as we get closer to having the electrical hooked up. Stay tuned.

Possible 500X2 @ 2ohm!!!!? I want one!!!!

Setup looks great!!!! Need me some front stage like that!! I too, but I am more of a leg man!! Bring on some vids!!

I'd get another mojo 15 and have the 4-15's! That should be good in a proper enclosure!

Cool One day I'll have to pick up some Russian. For the large following you seem to have in Russia it would pay off! Thanks for the vid!

to the SSA forum!!! Skip the 8's and just do the 12's in the bed. I don't think you would hear them over the 12's.

Thanks for sharing info on your new products!!! Great that you included measurements, that is good info!!!!

Blown away by the modding of the pearless enclosures!!!! Love all the pictures(never to many) the pics help tell the story!!! Can't wait to see the outcome of the FR88 pods!!

Damn! He does look like him!

Lookin' Good!!!! False floor blends right in like it came that way!!!!

Donation pending on me getting some of that sex....