smashedz28

What did you do to stop it Jullian?

I appreciate you guys helping. It's real odd to me. Last time it happend I wasn't paying too much attention. This time I did notice everything normal when I started it up. I took it to a drive through car wash so I was looking at the gauges. I was pushing the system hard as hell for almost 10 mins straight before I noticed. System is a sundown saz1500/btl 18 ran at 1 ohm. 2 kinetik hc2000's. Just 1 run back of 1/0 ( same wire under hood) and a mb quart 4125 discus for the highs. I'll check back when I get up in the morning. Thanks again I really appreciate it!

As in size of fuse? No. Different fuse than the first time? Yes It's hard for me to believe such a short run on a cheap ass ho alt can be the wires fault.. Alt is rated at 220a at like 1600 rpm. At idle I watch the needle drop dramatically. Hate this alternator. Shouldn't a 2' run of 1/0 knu Cca be good for a lot more than I have? I mean what else do I try? Run 2 runs of 1/0 just for the alt-bat connection? Lol seems a bit much.

It's basically a 2' cable. I checked the connections and there nice and tight. After it messed up the 1st time I replaced the entire piece and fuse holder. Each time it happens it completely melts that end of the fuse holder

Yea it's the cheaper of knu's cable. Rated for 250amps is what it says. Too much current? What's the fix for this?

The crescendos can be painted, I'll be getting mine done cause I hate that coper color. Just an idea I think they are bad ass amps

I'm leaving today to help a friend with his install. We're going to be soldering a bunch of 1/0 knu cca to the ring terminals. I noticed im out of the solder I used to have and I completely forgot what I had. Real simple. What kind of solder will be best for what I'm doing?

Thanks. Thats what I needed to know

Friend asked me about the phase dial on his sundown 1500. I couldn't give him an answer. What exactly is it and what does it do?

I know alot of you preach how worthless rear speakers are, I can understand if were talking about rear doors or something...my rear speakers are 6 x 9's mounted in the rear deck lid. Just playing around with my stock system its clear as day those speakers are back there and I'm going to replace them with after market speakers. The front stage will be a set of Rockford fosgate 6.5 components (T1652-S) using the passive crossovers it comes with. So... to keep with the fosgate theme for my speakers I see there is 2 different sets of power series 6x9's fosgate makes. 2 way and 3 way.. I understand what that means as far as how they operate but I'm not sure which one will be better coming from behind me in the vehicle? Both the same price. Maybe I'm over thinking it and it won't even matter, I don't know. Just looking for some opinions. Thanks

Also for what it's worth I'm going to be buying one of those big ass crescendo 1600.2's. Not sure if I want to try and use it in this build or not but its a possibility.. Too much power for a set of comps? Lol

Nothing in this vehicles sound system will be stock. I have about 80% of the equipment I'm going to use sitting here now. Like I said I'm going to put speakers in there regardless. I appreciate the comments.. Now about a better front stage.. What's better? I'm not fiberglassing my doors and I'm using stock locations. An active setup I'm sure would be better but that is something I've never done and I'm not sure this vehicle is the one to learn on. What's better? I'm not so worried about saving money for other things. I've been buying new stuff for this build since last year. No rush here. Changed my mind twice on amps.. Once after I already bought one lol.

Anything? Ideas. Comments, suggestions?

http://www.sonicelectronix.com/item_19510_Rockford-Fosgate-Power-T1693.html http://www.sonicelectronix.com/item_19509_Rockford-Fosgate-Power-T1692.html I also ran across some 6 x 9 component sets.. what's the deal with those?

I currently have one of those crescendo bass clef amps. Can't stand the color of the top plate. Does anyone know how I would go about changing the color? Would it have to be sent off to be anodized? I know nothing really about how that even works or who to send it off too. The writing on the top plate is etched in so as long as it isn't a thick paint or something I would imagine all that will still be there?? Just an off topic post.. What do you guys think?

That's what I needed to know. Thanks.

I'm helping a friend put together his system. This has to be such a rookie question but its something I've never had to deal with, all my systems I buy decks with enough RCA outputs. He refuses to spend money on a deck. He has a few laying around but only have 1 set of outputs on each deck. He plans to use 2 amps in his system (highs amp and sub amp) what's the best method to do this as far as running the rca's.

I hear that daily. My partner at work is a huge JL nuthugger. "you only need 1 W7... 2 is way too much". Lol.

Ok did some more research.. I sold him my old audiopipe 1500d. Wasn't sure about the output on it.. Here is an image Bridge in and out? I believe that's for linking purposes. Anyone got any idea and if that is not a usable output what is my next best option?

One more thing. The output is a front output. Any negative effects of using that for a sub channel and outputing from there to the highs amp? Reason I ask is cause the sub amp is the one with the output on it. I would think the crossover wouldntake care of that wouldn't it?

Buy a 3 sixty lmao. He is honestly the cheapest person I've ever met. Thanks bromo I knew those damn outputs were good for something lol..so simple I should have known. Thanks

Any pics jay cee ? Thanks for the advice everyone else.

I didn't pull the amp out of the box since posting this but it should be a beauty plate on the top.. Don't think the pcb will even be touched. Pretty sure under the plate is still the amp case.

Google is my friend lol. Found a few plating and chrome shops here local. I'll call around tomorrow. Thanks for the website. If all fails I'll be using them. I'll be sure to get some before and after shots whenever I do this

No not a show car.. In fact I'll rarely even see it. It's just something I would like to get done... Any reputable places I could send this off too? Not sure where to start to find a place like this locally.